Barranca Diamond BD10 Manuel du propriétaire

BD10 Power Feed Trim SawOwner’s Manual and Operating InstructionsCaution: Read all safety and operating instructions before using this equipment. This

10 BD10 OIL/COOLANTRoc Cut Roc Cut from Diamond Pacic is a new synthetic water soluble cutting additive with rust inhibit

11 BD10 SETUPTRANSPORTFor ease of transport, place the hood over the saw table and tape the hood to the table. All sawing lubricant sho

12 BD10 OPERATIONS AND ADJUSTMENTSPRE-START INSPECTIONPlace the BD10 Trim Saw on a flat surface such as a bench

13Fig. 5. Secure sludge plugSTART UPInspect the belt tension. Check the four motor mounting bolts (Fig. 6) to ensure they are tight and the motor is s

14START UPLock the clutch plates by turning the knob clockwise (Fig. 12). Be sure to securely tighten the knob on the vise as well (Fig. 17). Now enga

15Fig. 17. Vise adjustmentFig. 18. Vise cross-feed lockingSLAB SAWING MODEAt this point, the clutch should be engaged by turning the knob clockwise (F

16Fig. 22. Manual feed positionFig. 23. Loosen viseFig. 24. Rotate vise up TRIM SAWING MODESlabbing of rock material to uniform thicknesses using the

17The rock slab to be trimmed should rest flat and firmly on the saw table in front of the blade prior to moving the toggle switch to the LEFT/MANUAL

18Fig. 28. Remove belt guard Fig. 29. Belt tensionFig. 30. Adjusting belt tensionV-BELTThe BD10 Trim Saw blade arbor is powered by an AX-27 rubber V-b

19POWER FEED SYSTEM AND VISE Periodically the user should apply a thin coat of lubricating grease (wheel bearing or lithium grease) to the 3/8"-

2Thank you for selecting the Barranca Diamond BD10 Trim Saw. We are certain that you will be pleased with your purchase. Barranca Diamond takes prid

20Fig. 32. Blade arbor boltsBLADE ARBOR ASSEMBLY AND PULLEYSPeriodically, check the tightness of the four blade arbor housing mounting bolts (Fig. 32)

21DIAMOND BLADEPeriodically, the diamond blade on the BD10 Trim Saw will need to be resharpened should slow or poor sawing performance occur. Dull or

22Fig. 36. Convex or recessed side of blade flangeDIAMOND BLADE INSTALLATION AND REMOVALClose saw table and tighten the wing nut. Be sure that the pro

23NOTES

24 BD10 EXPLODED VIEW

25Item Part Description Part# Quantity1 Nut, Hex, 5/16 - 18 101196 42 Wrench, Tilesaw, 15/16 csd end 134684 13 Flange, Outer, 2 - 3/8 135830 24 Bearin

26Item Part Description Part# Quantity40 Table, Comp 168791 141 Assembly, Vise 168792 142 Vise Drive Motor Assembly 168795 143 Guard, Belt, Comp 16880

27Item Part Description Part# Quantity1 Screw, rnd hd, #8-32x1/2 152517 62 Screw, Hex HD FL 10-24x 5/16 159597 13 Switch, Feed Toggle, 15A, DPDT 16105

28 BD10 EXPLODED VIEW

29Item Part Description Part# Quantity1 Nut, Hex, 3/8 - 16 101188 22 Washer, Flat, SAE, 3/8 150923 33 Screw, 10 -32 x 1/2 Pan Head Phillips Machine 15

3SAFETY PRECAUTIONS Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in

30Barranca Diamond warrants to the original retail purchaser for a period of 1 year except as noted, from the date of purchase all products covered by

31SPECIFICS APPLICABLE TO LIMITED WARRANTY OF DIAMOND BLADES AND CORE BITSLaser Welded Blade and Bit Warranty If the laser weld between the segment an

32 BD10 SERVICE & WARRANTYREPLACEMENT PARTSReplacement parts for this tool may be ordered from your Barranca Diamond distrib

33NOTES

34NOTES

35NOTES

Barranca Diamond Products, Inc.1315 Storm ParkwayTorrance, CA 90501Toll-Free: (800) 421-5830Phone: (310) 539-5221Fax: (310) 539-5158www.barrancadiamo

4ROTATING OR MOVING PARTSKeep hands, feet, hair, and clothing away from all moving parts to prevent injury. Never operate the saw with covers, shrouds

5DIRECTION OF FEEDAlways feed work into a blade or cutter in the direction shown in this manual. All blades, grinding wheels or polishing belts shoul

6 BD-10 SAFETYWARNINGCALIFORNIA PROPOSITION 65 MESSAGESILICA DUST WARNINGGrinding/cutting/drilling of masonry, concrete, metal and other

7ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONSIn order to prevent potential electrical shock and injury, the following electrical safety precauti

8To avoid the possibility of the appliance plug or receptacle getting wet, position the saw to one side of a wall mounted receptacle. This will preve

9Main Motor Leeson A4SI7DR56Horsepower 1/3 HPMotor Voltage 115 volt/60Hz / 220 volt/50HzAmperage 5.8 Amps / 3.5 AmpsMotor RPM 1725 RPM Fixed / 1425 RP